VapeWholesaleHub  |  Wholesale supplier · Shenzhen, China
Tel / WeChat / WhatsApp: +86 13711127975  |  vape@0099933.xyz
Home  /  Vape Cartridge  /  Vape Cartridge packaging and carton specs entry level
vape cartridges · first-time buyers

Vape Cartridge packaging and carton specs entry level

If you are comparing three quotes for vape cartridge, compare the paperwork first. Test reports, artwork files, batch coding and the replacement clause tell you more about a supplier than the unit price on page one.

Published 24 March 2026  ·  VapeWholesaleHub  ·  Reading time 9 min

Surface finish under raking light, one of the cosmetic checks.
Surface finish under raking light, one of the cosmetic checks.
Vape Cartridge packaging and carton specs entry level configuration from a production run, photographed before packing.
Vape Cartridge packaging and carton specs entry level configuration from a production run, photographed before packing.

Lead times, freight and landed cost

Vape Cartridge is a specification decision before it is a price decision. Get the resistance, the capacity and the packaging right and the price conversation becomes short. Get them wrong and no discount will rescue the order.

If you dropship, we can label cartons to your format and omit our documentation from the outer box. It is a small operational detail that decides whether your customer sees a supplier or a partner.

We ship from Shenzhen and Guangzhou: air express for samples and part loads, sea freight for volume. Typical production lead time is 28 working days after artwork approval, plus transit. We quote both routes so you can see the trade-off instead of guessing at it.

What we test before a carton is sealed

Leak complaints almost always trace back to one of three things: an over-torqued centre post, a seal that sat in a hot container, or a fill volume pushed past the design limit. We cap fill volume slightly below maximum for exactly that reason.

Battery safety is not a marketing line. Cells are matched by capacity and internal resistance before assembly, charging boards are checked for cut-off voltage, and any unit that fails the cut-off test never reaches packing.

For first-time buyers, the practical answer is usually a shorter range: two core lines, one step-up, one trial SKU. Everything else is inventory risk wearing a nice finish.

Compliance without the last-minute scramble

Labels are where good orders go wrong. Nicotine warnings, child-resistant closures, batch coding and market-specific text all have to be correct before the pallet leaves. We prepare test reports, declaration of conformity and safety data sheets for each shipment and we ask for your destination list early so artwork matches the market.

If you sell into a market that requires child-resistant packaging, say so at quotation stage. Retrofitting a CR closure onto a finished bottle design usually means a new mould and a four week delay.

  • Reference sample retained from every batch
  • Cartons drop-tested and pallet-counted for clean freight
  • Consolidated or split shipping, quoted both ways
  • Document pack prepared per destination market
  • Mixed SKU cartons to spread first-order risk
  • Specification locked in writing before production starts

How we structure a first order

When you compare suppliers for vape cartridge, ask for the last three production dates on the same SKU. If the answers are vague, the specification is not being held and the next batch will not match the sample you approved.

We keep a short list of approved configurations for vape cartridges. Anything outside that list is possible, but it becomes a custom run with a custom lead time, and we quote it as such rather than pretending everything is standard.

Specification summary

Typical specification for this category
Volume2.0 ml
CoreCotton
Resistance1.5 ohm
Thread510 thread
AirflowBottom
PackagingBlister
Minimum order300 units per SKU, mixed cartons allowed
Lead time18 working days after artwork approval

None of this is complicated. It is just written down, which is more than most buyers get before they wire a deposit.

Frequently asked

How do you handle repeat orders?

The specification is held on file against your account, so a reorder is a reference rather than a new brief. We recommend a standing schedule with a fixed weekly cut-off so stock lands before the shelf empties.

What happens if part of the order is defective?

Report within seven days with photos and the batch code. Confirmed defects are replaced or credited on the next shipment. The failure is logged by mode and batch, and reviewed monthly with the factory.

Can we order samples before committing?

Yes. Sample orders are shipped by air express and the cost is credited against your first production order above 60 units. We would rather you handle the sample than approve a specification from a photograph.

Related reading

Need a quotation on vape cartridges?

Send destination market, target price and quantity. Same-day reply on working days.

Tel / WeChat / WhatsApp +86 13711127975  ·  vape@0099933.xyz

Talk to the supply team

Ask for a quotation on vape cartridges

Tell us the market you sell into and the price band you work in. You will get a specification and a landed cost estimate, not a catalogue dump.

What to send

Destination market, target retail price, quantity per SKU, and whether you need private label. With those four lines we can quote the same day.

Samples ship by air express and the cost is credited against your first production order.

Email the team
WhatsApp Email us