Vape Cartridge customs basics guide
Ordering vape cartridge is not difficult. Ordering vape cartridge that sell through without a return queue behind them is the part most buyers underestimate, and it is where we spend our time. We supply first-time buyers in European and North American markets with core lines that turn over predictably, and we keep the specification list short enough for your team to actually manage.
Published 25 April 2026 · VapeWholesaleHub · Reading time 9 min
Assortment planning without the guesswork
Buyers come to us for vape cartridge after a bad quarter: dead stock on one side, empty shelves on the other. The cause is usually the same, an assortment built from a catalogue instead of from sell-through data. This page explains how we rebuild that balance for first-time buyers.
We keep a short list of approved configurations for vape cartridges. Anything outside that list is possible, but it becomes a custom run with a custom lead time, and we quote it as such rather than pretending everything is standard.
Most first-time buyers arrive with a spreadsheet and leave with too many SKUs. The fix is not a bigger catalogue, it is a narrower core. We normally propose three tiers: a volume line that carries the shelf, a step-up line that lifts basket value, and one trial SKU that tells you what to order next season.
Paperwork, labelling and market rules
Labels are where good orders go wrong. Nicotine warnings, child-resistant closures, batch coding and market-specific text all have to be correct before the pallet leaves. We prepare test reports, declaration of conformity and safety data sheets for each shipment and we ask for your destination list early so artwork matches the market.
If you sell into a market that requires child-resistant packaging, say so at quotation stage. Retrofitting a CR closure onto a finished bottle design usually means a new mould and a four week delay.
The reorder is the real test
For private label accounts we hold the artwork files and the approval record. Rebranding a line eighteen months later is then a file update instead of a redesign.
The replacement policy is deliberately simple: report within seven days of delivery with photos and the batch code, and we replace or credit at the next shipment. We do not argue about a defect we can see in a photograph.
- Cartons drop-tested and pallet-counted for clean freight
- Artwork proof plus physical dummy for custom packaging
- Reference sample retained from every batch
- Standing reorder schedule with a fixed cut-off
- Consolidated or split shipping, quoted both ways
- Seven-day defect reporting with replace-or-credit
Batch consistency and why it matters
14 separate checks run before a carton is sealed: electrical, mechanical, leak, finish and packaging. Anything outside tolerance is quarantined the same day and reported to you, rather than shipped with a hope and a discount.
Leak complaints almost always trace back to one of three things: an over-torqued centre post, a seal that sat in a hot container, or a fill volume pushed past the design limit. We cap fill volume slightly below maximum for exactly that reason.
Specification summary
| Volume | 2.0 ml |
| Core | Cotton |
| Resistance | 1.5 ohm |
| Thread | 510 thread |
| Airflow | Bottom |
| Packaging | Tube |
| Minimum order | 300 units per SKU, mixed cartons allowed |
| Lead time | 22 working days after artwork approval |
We would rather lose an order at quotation stage than explain a mismatch after delivery, which is why the specification conversation comes before the price conversation.
Frequently asked
What happens if part of the order is defective?
Report within seven days with photos and the batch code. Confirmed defects are replaced or credited on the next shipment. The failure is logged by mode and batch, and reviewed monthly with the factory.
How do you handle repeat orders?
The specification is held on file against your account, so a reorder is a reference rather than a new brief. We recommend a standing schedule with a fixed weekly cut-off so stock lands before the shelf empties.
What is the minimum order for vape cartridge?
Standard configurations start at 500 units per SKU, with mixed SKUs allowed inside the same carton. Custom colours, custom packaging or a private label run usually start at 1000 units because of setup time on the line.
Related reading
Need a quotation on vape cartridges?
Send destination market, target price and quantity. Same-day reply on working days.
Tel / WeChat / WhatsApp +86 13711127975 · vape@0099933.xyz