VapeWholesaleHub  |  Wholesale supplier · Shenzhen, China
Tel / WeChat / WhatsApp: +86 13711127975  |  vape@0099933.xyz
Home  /  Vape Cartridge  /  Sourcing Vape Cartridge: contract and PO terms deep dive
vape cartridges · first-time buyers

Sourcing Vape Cartridge: contract and PO terms deep dive

If you are comparing three quotes for vape cartridge, compare the paperwork first. Test reports, artwork files, batch coding and the replacement clause tell you more about a supplier than the unit price on page one.

Published 17 April 2026  ·  VapeWholesaleHub  ·  Reading time 5 min

Sourcing Vape Cartridge configuration from a production run, photographed before packing.
Sourcing Vape Cartridge configuration from a production run, photographed before packing.
Surface finish under raking light, one of the cosmetic checks.
Surface finish under raking light, one of the cosmetic checks.

How the price is actually built

Buyers come to us for vape cartridge after a bad quarter: dead stock on one side, empty shelves on the other. The cause is usually the same, an assortment built from a catalogue instead of from sell-through data. This page explains how we rebuild that balance for first-time buyers.

We publish a realistic band of 1.98 to 5.48 per unit for standard configurations at 50 units. Below that band you are buying a lighter specification; above it you are paying for finish, packaging or a smaller run.

A landed cost sheet for vape cartridge has five lines: unit price, packaging, freight, duty and the cost of defects. Quoting only the first line is how buyers end up surprised at the fourth.

Getting the documents right

Labels are where good orders go wrong. Nicotine warnings, child-resistant closures, batch coding and market-specific text all have to be correct before the pallet leaves. We prepare test reports, declaration of conformity and safety data sheets for each shipment and we ask for your destination list early so artwork matches the market.

If you sell into a market that requires child-resistant packaging, say so at quotation stage. Retrofitting a CR closure onto a finished bottle design usually means a new mould and a four week delay.

For first-time buyers, the practical answer is usually a shorter range: two core lines, one step-up, one trial SKU. Everything else is inventory risk wearing a nice finish.

The checks behind every shipment

Cosmetic grading is written down, not argued about. Minor scuffs inside the tolerance band are accepted; anything that would make a customer put the unit back on the shelf is rejected. Your staff should never have to explain a finish defect to a paying customer.

Battery safety is not a marketing line. Cells are matched by capacity and internal resistance before assembly, charging boards are checked for cut-off voltage, and any unit that fails the cut-off test never reaches packing.

  • Reference sample retained from every batch
  • Seven-day defect reporting with replace-or-credit
  • Private label files archived for future rebrands
  • Artwork proof plus physical dummy for custom packaging
  • Document pack prepared per destination market
  • Named account contact who has handled the product

What happens when something goes wrong

Returns are handled as data, not as complaints. Every reported failure is logged by mode and by batch, and the pattern is reviewed monthly with the factory.

The replacement policy is deliberately simple: report within seven days of delivery with photos and the batch code, and we replace or credit at the next shipment. We do not argue about a defect we can see in a photograph.

Specification summary

Typical specification for this category
Volume2.0 ml
CoreMesh
Resistance1.8 ohm
ThreadPress-fit
AirflowBottom
PackagingBlister
Minimum order300 units per SKU, mixed cartons allowed
Lead time12 working days after artwork approval

We would rather lose an order at quotation stage than explain a mismatch after delivery, which is why the specification conversation comes before the price conversation.

Frequently asked

Can you ship to multiple locations?

Yes. Split shipments are quoted separately because consolidation and splitting price differently. Tell us the destination list at quotation stage and we will show both options.

Do you support private label?

We do. Send your artwork or your brand direction and we will return a digital proof, then a physical dummy for colour approval. Packaging files stay on record so a rebrand later is a file update rather than a redesign.

How do you handle repeat orders?

The specification is held on file against your account, so a reorder is a reference rather than a new brief. We recommend a standing schedule with a fixed weekly cut-off so stock lands before the shelf empties.

Related reading

Need a quotation on vape cartridges?

Send destination market, target price and quantity. Same-day reply on working days.

Tel / WeChat / WhatsApp +86 13711127975  ·  vape@0099933.xyz

Talk to the supply team

Ask for a quotation on vape cartridges

Tell us the market you sell into and the price band you work in. You will get a specification and a landed cost estimate, not a catalogue dump.

What to send

Destination market, target retail price, quantity per SKU, and whether you need private label. With those four lines we can quote the same day.

Samples ship by air express and the cost is credited against your first production order.

Email the team
WhatsApp Email us